HID-Cosmo

  • CDM-Elite Electronic Ballast 315W
  • CDM-Elite Electronic Ballast 315W
  • CDM-Elite Electronic Ballast 315W

CDM-Elite Electronic Ballast 315W

Features:
Long life span(up to 60,000 hours )
Low frequency operation ,eliminating light slash frequency
Quicker light start function
Perfect protection function
Compact type, easy to install
contact

HID-CDM Elite

Electronic Ballast Special for CDM Elite TMW Lamp

Product Features and advantages

1. Special Electronic Ballast

2.The long life span is up to 60,000 hours

3.Low frequency operation ,eliminating light slash frequency

4.Quicker light start function

5.Perfect protection function

6.Compact type, easy to install

7.160~264 wide range operating voltage

8.The light end-of-life protection function

9.More dimming series


Application

Outdoor Lighting

Dimensional Drawing


Standard and Certificates

1.Safety:/EN61347-2-12

2.THD:EN61000-3-2

3.EMC EMS :IEC61547

4.EMC EMICISPER15 ed7.2

5.Vibration test:IEC68-2-6-Fc

6.Impact test:IEC68-2-29-Eb.IEC60068-2-27

7.Certificate: CE, CQC,RoHs,CCC

8.Quality standard:ISO9001

9.Environment standard: ISO14001


Dimension (mm)

Product model

A1

A2

A3

B1

B2

B3

C1

D1

CDM ELITE AC220V 210

215

201.8

179

96

98.6

80

59.5

5

CDM ELITE AC220V 315

215

215

179

96

98.6

80

59.5

5





HID-CDMELITE

Technical Parameters

Product model

Light source

Operating Voltage (V)

System power (W)

Voltage range (V)

Power Factor

T-case Max.) (°C)

Ambient temp. (°C)

BST2210A/CDM ELITE AC220V 210

CDM Elite210

AC220V

210W

160-260

0.95

-30°C..+50°C

80°C

BST2315A/CDM ELITE AC220V 315

CDM Elite315

AC220V

315W

160-260

0.95

-30°C..+50°C

80°C










Installation Technical Parameters

1.Rated power supply voltage:220v-240v

2.Performance voltage:+6%..-10% 198-254V

3.Safe Voltage:180-264V

4.Frequency:50/60Hz

5.Operating Frequency(Typical):140Hz

6.Starting Voltage:3-5KV

7.The space from any charged (metal) components to the earthing (Grade I)or test (Grade II) and creepage distance>5mm

8.Leak Current: every ballast<0.7 Ma

9.Load capacity Max.120Pf


IP Grade

1.EOL protection for luminaire

2.Short circuit protection

3.Over temperature protection


Notes

1.In the case of a three-phase power supply,do not disconnect the neutral wire; otherwise the circuit may be damaged

2.Ballast could withstand the 3 times voltage drop(>10ms), then should turn off and restart the power supply, to reset the ballast

3.To achieve the appropriate electromagnetic compatibility, the internal circuit of lighting devices should be short type circuit as far as possible; the power line should not be in flat with the line of luminaires.

4.Overheating fixtures automatically start ,the fixture could be used 20mins at most

5. Could not operate 24hours all day


Notes

1.The above data is obtained when the power supply impedance value is set to 400mΩ(Equivalent to the wire of 15m long 2.6m2 cross-sectional area wire plus 20m connected to the 2.

middle position of power distribution systemreflecting the ballast use quantity in the worst case , then if the power supply impedance value is set to 800mΩ,the number of the ballast may be increased by 10% on ths basis.

2.  The obtained measured value can be verified in the actual installation ,the data may be changed

3.  Sometimes ,the factor that determined the max. using number is not the switch type but the max. load power switch

4.  Note: Only when the wall switch and all the other switches, is open at the same time, can the using single-stage circuit breaker be obtained when measured in the case of largest number of ballasts. If using multiple circuit breaker, the number of ballast is suggested to decrease 20%.

5.  30mA residual current detector can at most connect 30 ballasts once


The The current in the circuit with voltage 200V

Electronic Ballast

Input Current(A)

CDM ELITE AC220V 210V

0.96

CDM ELITE AC220V 315V

1.44





The number conversion table of ballasts that other types miniature circuit breakers could connect at most

MCB Model

Capacity

Relative Value of Ballast Number

B

16A

100%(see the table above)

B

10A

60%

C

16A

170%

C

10A

104%

L,I

16A

108%

L,I

10A

65%

G,U,II

16A

212%

G,U,II

10A

127%

K,III

16A

254%

K,III

10A

154%













Order and Packing Information

  • number
  • title
  • time
  • download

Contact US


Production Base: 4/F,7th Building, Jiaanda Industrial Park, Huafan Road

Longhua New District,Shenzhen, China

Sales hotline: 13798250413

Sales calls:0086-0755-29179085

Email :sales01@bersn.com

Friendship Link: 中文官网 |

SMART Lighting Control System LED Street Light LED Driver HID Electronic Ballast

2001-2013 Copyright © SHENZHEN BERSN OPTO-ELECTRONICS CO., LTD All images, text should not be copied without permission.  Technical:Ctmon